High visibility winter Jacket Pesso Lyra, yellow

Qualities & Benefits

Outer material: Ripstop waterproof fabric. EN ISO 20471 Class 2
A special moisture-proof TPU membrane allows the body to breathe and wet vapor outside.
Insulation: Synthepone PET. Sealed waterproof seams.

EN ISO 20471 Class 2
Hood: Spacious, adjustable, detachable zippered hood.
Segmented reflective tapes.
Pockets: functional zipped pockets. Two waist pockets, a chest pocket, and inside pockets.

Sizes: S-3XL
Color: HI-VIS yellow, black

Fabric: 100% Polyester RIPSTOP
Lining: 100% Polyester
Padding: 100% Polyester

STANDARD
EN ISO 20471:2013+A1:2016 Class 2

RIPSTOP fabrics feature woven fabrics using a special reinforcing technique that makes them resistant to tearing and ripping. During weaving, (thick) reinforcement threads are interwoven at regular intervals in a crosshatch pattern.

Advantages of rip-stop are the favorable strength-to-weight ratio and that small tears cannot easily spread. Rip-stop fabrics are used in yacht sails, hot air balloons, kites, parachutes, remote control hovercrafts, camping equipment, and other applications requiring a strong lightweight fabric. Rip-stop reinforcement is incorporated into heavier fabrics requiring extreme durability.

STANDARD
EN ISO 20471:2013+A1:2016 Class 2

Protective garments with enhanced visibility. High visibility garments have fluorescent surfaces and reflectors that conform to certification requirements on the design according to three different classes and have been tested before and after washing.

Size	C44/XS	C46/S	C48/M	C50/M	C52/L	C54/L	C56/XL	C58/2XL	C60/XXL	C62/3XL
A Chest measurement cm	88	92	96	100	104	108	112	116	120	124
B Waist measurement cm	76-79	80-83	84-87	88-91	92-96	97-101	102-107	108-113	114-119	120-125
C Seat measurement cm	94	98	102	106	110	114	118	122	126	130
D Inside leg measurement cm	80	80	82	82	82	82	84	84	84	84

Take measurements whilst in your underwear. Use a tape measure. Remember to keep the tape measure tight when measuring, without pulling it. Measure according to instructions and compare your measurements with the right table. All measurements in the tables are close body sizes.

A Chest width. Measure over the widest part of the chest.
B Waist width. Measure where you normally have your waistband.
C Seat width. Measure over the widest part of the seat.
D Inside length measurement: Measure along the inside of the leg, from fork to floor.

EN ISO 20471

Protective garments with enhanced visibility. High visibility garments have fluorescent surfaces and reflectors that conform to certification requirements on the design according to three different classes, and have been tested before and after washing. 5 washes is the minimum and if the garment has been tested and approved for a higher number of washes this should be stated on the care label.

CLASS 1

Protective garments fitted with fluorescent fabric, with an area of at least 0.14 m≤ and reflectors with an area of 0.10 m≤, for use where the lowest level of visibility is demanded.

CLASS 2

Protective garments fitted with fluorescent fabric, with an area of at least 0.50 m≤ and reflectors with an area of 0.13 m≤, for use where the visibility requirement is not as high as class 3.

CLASS 3

Protective garments fitted with fluorescent fabric, with an area of at least 0.80 m≤ and reflectors with an area of 0.20 m≤, where the highest level of visibility is demanded. Protective garments must cover the torso and at least have sleeves or full-length trousers. The reflectors must wrap around the torso and arm or leg. Minimum reflector width must be 50 mm.